Is your Carpet looking a bit dull? The colors are a bit off and there seem to be quite a few stains that have not been removed completely. If that is the case, then, what your carpet needs is a thorough deep cleaning.

Step 1: Get rid of the Furniture

The first thing you need to do is get rid of anything that would get in the way of your carpet cleaning. Remove all the furniture and other knickknacks. Move them to another room. Clear the room completely before you start deep cleaning the carpet.

Step 2: Vacuum

Before you deep clean, you need to vacuum the carpet thoroughly. Make sure you cover every inch of the carpet. You can divide the carpet into smaller sections and vacuum each section one at a time. This way, you won’t miss any area of the carpet.

Always make sure you vacuum both the upper and the underside of the carpet (for detachable rugs). First, vacuum the upper surface of the carpet. Then flip the carpet and vacuum the underside thoroughly. After that, flip the carpet back to its original position and vacuum the upper side once more.

Additional tip: To get a better result from vacuuming, sweep your carpet with a broom first. This will lift the carpet fibers and displace the dirt within, which helps your vacuum cleaner pick up more of the dirt hidden in your carpet.

Step 3: Pre-treat the stains

The next step in deep cleaning is pre-treating the stains. Just as you pre-treat stains while doing laundry, you need to treat stains before cleaning carpets as well. Here is how you pre-treat stains:

Things you’ll need:

  • Vinegar
  • Water
  • Clean Cloth
  • Spray bottle
  • Steam Iron

What to do:

  1. Mix one part vinegar with two parts of water.
  2. Pour the mixture in a Spray bottle.
  3. Spray the mixture over the stain
  4. Wet a piece of cloth.
  5. Put the damp cloth over the stain
  6. Put your iron on steam setting.
  7. Iron over the damp cloth for about 30 seconds.
  8. Repeat the process until you no longer see the stain.

Step 4: Steam Clean the Carpet

This is the most important part of the deep cleaning process. While there are other processes like dry cleaning that you can use, steam cleaning is the most recommended method for deep cleaning your carpet. Unlike other deep cleaning methods, steam cleaning uses very little chemicals, making it the safer option. Here is how you steam clean your carpet:

Things you’ll need:

  • Steam Cleaner
  • Hot water
  • Carpet shampoo/ vinegar and essential oil

What to do:

  1. Remove the water container and fill it with hot water
  2. Add appropriate carpet cleaner. You can either use a carpet shampoo or, if you want to use natural ingredients, vinegar.

Quick Tip: Dilute vinegar with water before using it as a carpet cleaner. Use higher ratio of vinegar on high traffic areas and lower ratio of vinegar in low traffic areas.You can also add a few drops of essential oils in the mixture for a fresh smelling carpet.

  1. Run the steam cleaner over your carpet. Make sure you cover every inch.

Quick Tip: As with the vacuum cleaner, you can divide the carpet into sections so as to avoid missing any area.

  1. Repeat step three until the carpet is thoroughly cleaned. Run the steam cleaner more often over the high traffic areas.
  2. Remove the dirty water and carpet cleaning solution from the steam cleaner and pour another clean batch of hot water on the water container.
  3. Run the steam cleaner over the carpet once more. This will rinse out the carpet cleaner you used.
  4. Allow the carpet to dry.

Step 5: Use a Carpet Freshener

The final step is deodorizing your carpet. To do this, you can either buy a carpet deodorant from the store or you can create your own home-made carpet deodorant. If you’re buying a carpet deodorant, you can simply follow the instructions given on the bottle. On the other hand, if you’d like to make your own carpet deodorant, here is how you do it:

Things you’ll need:

  • 1 Cup of baking soda
  • 10-20 drops of essential oil
  • ½ cup of borax (if you have pets)

What to do:

  1. Mix all the ingredients in a bowl.
  2. Lightly sprinkle the mixture over your carpet
  3. Let the mixture sit in the carpet for about half an hour
  4. Vacuum the carpet thoroughly. Make sure you remove all of the mixture from the carpet.

Congratulation, You’re Done!!!

Leave a Reply